Develop and supply a PCB for small RC car

$250-750 USD

W trakcie realizacji

Opublikowano

ponad 7 lat temu

$250-750 USD

Płatne przy odbiorze

Specification for RC controller board Overview The board is to be a 2 channel Radio receiver and speed controller to operate a small RC car. The board should be no bigger than 30mm x 20mm Details a) Flysky compatible receiver to work with FS-GT2B or FS-GT3C 2.4Ghz transmitters b) To work off a single cell 3.7v LiPo battery . c) Circuits to be reverse voltage protected. d) Atmel based processor (Arduino, ATtiny etc) with firmware included. e)Microcontroller is to be externally programmable via pads on side of board using FTDI TTL 232R 3v3 USB or similar. f) Reversible Electronic speed controller with no brake to drive a small DC motor (approx 2A max) g) Additionally 2.54mm spaced solder pads are to be provided for the following connections. Positive and Negative motor outputs. Signal, Ground and Positive for steering servo Positive and negative Battery connections h) Intellectual property and copies of PCB design and firmware is to be supplied to me. It should not be divulged to third parties. Boards are to be supplied complete with firmware installed. Initial order of 20 units.

Identyfikator projektu: 11516589

Informację o projekcie

12 ofert

Zdalny projekt

Aktywny 8 lat temu

Szukasz sposobu na zarobienie pieniędzy?

Adres e-mail

Korzyści ze składania ofert na Freelancer.com

Ustal budżet i ramy czasowe

Otrzymuj wynagrodzenie za swoją pracę

Przedstaw swoją propozycję

Rejestracja i składanie ofert jest bezpłatne

Przyznano:

@rraduconstantin

Hello, I am a certified EE engineer with more than 6 years of experience designing building and testing electronic devices. I work as a r&d engineer in a lab, and in my spare time I freelance. I can help you with every aspect of your product. I have designed and built several brushless ESCs based on Atmel microcontrollers. And one Flight controller based on the F3 chip from ST. I am very pasionate about RC Models. I have a home build drone with a home made controller (based on the atmega). This is a big project and I recommend you separate it into several smaller ones. The bid is for the design and programming of the controller. The costs for testing and producing all the boards will vary depending on the board type, components, etc. and is not comprised in the bid. Depending on what you want, the bid is negotiable. If you have any questions please contact me. Thank you.

$480 USD w 10 dni

5,0

(3 opinii)

2,2

12 freelancerzy składają oferty o średniej wysokości $512 USD dla tej pracy

@pcbdcs

Hello, I have been associated with Hardware design (Circuit / Electronics design), PCB design, Library creation and Library database maintenance, PCB Manufacturing, Component procurement, PCB Assembling and Functional testing for over 9 years. I have used various CAD/EDA tools for PCB design. Would you prefer any specific EDA tool for PCB design (or) any tool is okay? I will provide the PCB Manufacturing, Component procurement, PCB Assembling & Functional testing services too. I would like to take this up and are fully equipped to deliver the required files. So, if you'll give me a chance to take part to your work, I will respond in the same manner, handling you good quality projects, as soon as possible. I look forward to hearing from you! Wish you a nice day! Thanks & Regards, Karthik

$450 USD w 10 dni

4,7

(27 opinii)

5,4

@dennuar

Hello! I am interested in your offer! I have experience in programming and pcb layouting (over 10 years) for power electronics with microprocessors PIC (microchip), AVR (ATMEL), STM32 (STeleсtronics) and Arduino's. I recently registered here, and willing to work for a small cost, because I need to improve the rating. Examples of my work you can see in the portfolio Waiting for your reply. Best regards, Denis Mark.

$250 USD w 6 dni

5,0

(22 opinii)

4,3

@VenuVasam

Hi, Its simple task and I can deliver complete project including schematic and firmware with the best quality and on time. My skills: I've excellent embedded system design skills from the electronics component selection to the documentation including schematic design, firmware/application development, maintenance. Apart from Skills: Also I'm happy to provide you after delivery support such as any clarifications/upgrades on hardware or software. Looking forward to work with you. Thanks and kind regards, Venu

$555 USD w 10 dni

5,0

(1 opinia)

2,2

@gilsonvarghese

I am an electronics and communication engineer. I have worked in an FPGA based solutions company. I have done projects that electronics design. I do hobby projects like creating a drone which does all image processing with arm processor and Linux. I have read your specs carefully and googled the specific parts you want. I will accomplish the task and I hereby put forth my milestones. Please award me the project. Contact me if you need any clarifications. Lets discuss details over freelancer conversation and email.

$650 USD w 10 dni

0,0

(0 opinii)

0,0

@Ahmedboukhriss

Hello dear Client ! I am very motivated for this mission with all of your requirements. Actually, I ’m an Electronics and Embedded engineer with a good experience especially in programming microcontrollers and electronics design using Altium design and Eagle pcb Tools and i'm ready for this challenge to deliver a top quality work. Please contact me to discuss this mission more. I confirm my avaibility to finish your project on time. Thank you for your consideration Best Regards Boukhriss Ahmed

$611 USD w 15 dni

0,0

(0 opinii)

0,0

@spookymelonhead

Hi, I have good experience working with RC controlled vehicles. I'm currently working as UAV Engineer. I can design good PCBs with minimal EMI and would be able to understand your needs in the design clearly. Regards, Hardik Madaan

$500 USD w 10 dni

0,0

(0 opinii)

0,0

@Kumayl77

Hi. I am an intense DIY freak and have made some great projects related to electronics and rf amplifiers. I plan to use the arduino board to do this project. I prefer to use proteas for PCB designs and fabrication but i am proficient with Altium too if that is required. Given the oppurtunity i can make the PCB designs of those devices listed. We can discuss the milestones to achieve on the chat.

$300 USD w 12 dni

0,0

(0 opinii)

0,0

@robertobizzarri

Nice Job! I am an RC car enthusiast too. It is not clear the receiver. It must be done all over again? Otherwise there are many modules ready for use.

$833 USD w 15 dni